We've encountered this great article pertaining to How to Install a Bathtub listed below on the internet and figured it made good sense to relate it with you on this site.
Installing a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately difficult task. If the old bathtub is easily available, the project can move immediately; if you have to open a wall to get rid of the old bathtub as well as position the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub and set in the brand-new one. Make certain you have certified on your own for the task and fit trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might require a professional plumber to make tube links.
This post will certainly assist you set up a new bath tub in your washroom if you have actually already bought a new bathtub and also do not need to change the setup of your previous water system pipes.
Your tools and also product checklist need to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in area in between the faucet and the sink. Secure the tap in place with the maker offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former type must be linked to the faucet ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has been used at least when as this will settle it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill the tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about Installing A Bathtub? Try to leave a remark down the page. We would be pleased to know your opinion about this write-up. We are looking forward that you come back again in the near future. Kindly take a moment to distribute this blog entry if you appreciated it. I recognize the value of reading our article about How to Install a Bathtub Yourself.
Free Estimate